Results 1 to 23 of 23

Thread: Aniline Wax Pull-up - How to Restore Aniline Wax Pull-up Leather Sofa?...by Jermaine.

  1. #1
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default Aniline Wax Pull-up - How to Restore Aniline Wax Pull-up Leather Sofa?...by Jermaine.

    And here are the pictures merged from the previous thread taken on-location!

    #1


    #2


    #3


    #4

  2. #2
    Join Date
    Jun 2009
    Posts
    106

    Default How to Restore Aniline Wax Pull-up Leather Sofa?




    #2



    #3



    #4



    #5



    #6



    #7



    #8



    #9



    #10



    #11



    #12

  3. #3
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Received the sample and here are the recommended procedure:

    Tarnish Brass:
    Use d'Tarnish-1.3 to wipe the tarnish brass - test it out with cotton swab if the stain response.

    Attention to Stains:
    Surface contact areas that has rings may be alkaline stains.
    Using Degreaser-2.2 or Acidifier-2.0 to neutralize alkaline ring marks will reduce blotchiness.
    In other words the entire panel having the same pH value 3-5 will reduce blotchiness.
    The entire panel has to be acidified to condition the protein fiber cationic (+) to hydrogen-bond with other anionic (-) leather constituent to be applied at the next relevant stage - especially the Aniline Pure-21 and the Fatliquor-5.0.
    Hydrating the leather structure with Hydrator-3.3 further assist to even out the pH value of the leather structure.

    Prep Cleaning:
    Prep cleaning process prepares the leather free from foreign soil contamination.
    Prep4.4 is leather-safe design for absorbent leathers as this is Aniline Wax Pull-up leather.
    Use Prep4.4 > Cleaner3.8 > Rinse3.0 in combination with horsehair brush agitation and leather Eraser4 scrubbing follows by paper rag extraction.
    Let it dry, erase with leather Eraser4 and inspect if there are grease stains.

    Degreasing:
    Degreasing with Degreaser2.2 > rinse3.0 to remove grease stains if any.
    Let it dry, erase suspended residue and inspect ready for dyeing.

    Aniline Redyeing:
    There are three versions of aniline dyes:
    Aniline T’parent27, AnilineT’lucent25 and Aniline Pure21.
    Aniline Pure21 is the penetrating dyes and is the one to be used to stain the leather crust.
    This is applied by spray and pad off excess with lint-free paper rag to achieve an even appearance when dry.
    When the dyeing is satisfactorily done and inspected we may proceed to restore the leather structure.

    Leather Rejuvenating:
    Rejuvenating the leather is to return the leather to its original suppleness and strength that may include reducing the creases and wrinkles.
    It’s a threefold process that involves hydrator3.3 > fatliquor5.0 > rinse3.0.
    The hydrator3.3 when soaked, wrapped and dwelled overnight will cause the crushed, stick together fibrils to relax.
    The dwelling facilitates colloidal water movement within the leather structure capillary motion during the wicking process.
    That will cause suspended soil particulates to be moved to the leather surface to be extracted with rag while damp and erase with leatherEraser4 when dry.
    Other penetrated stain removal technique is to lay layers of tissue paper follows with towel to weight them down causing the wick-up stains to be trapped by the tissue.
    While the leather is still moist fatliquor it till saturation, another application is recommended when the leather is moist again.
    When almost dry rinse the remaining traces of fatliquor with rinse3.0 until the leather feels squeaky.
    Leave till dry and inspect, to reduce darkening effect and soften the leather stretch or flex it.

    Wax Pull-Up Rejuvenating:
    WaxEffect8.6 is used to rejuvenate wax pull-up effect diminished through usage, ageing or cleaning.
    The application method is similar to fatliquoring.
    On natural slow drying minimum four hours or until residual wax appears on the surface.
    This cloudy residual wax is activated with a heat gun or hair dryer to coats the leather grain.
    In restoration refinishing to the leather originality urethane topcoats further protects this wax coating.

    Adhesion Coat:
    Adhesor73 is fine sprayed and excess is pad off like varnishing to ensure that the topcoats have a better foundation to bite into.

    Aniline Dye Coat:
    Here is the chance to rectify the colors if necessary by dye coating to even out appearance prior to the topcoat with Aniline T’parent27.

    Topcoat:
    Topcoat Aniline79G, an aqueous urethane topcoat gloss is recommended to protect the leather with excellent toughness and flexibility.

    Feelcoat:
    Leather Scent-D is recommended for this Aniline Wax Pull-up leather with the following benefits:
    It’s a non-film forming, non-stick protector that enhances a draggy-feel with a classic leather scent that charms
    It imparts a non-stick breathable barrier essentially to shield the detrimental effects of sticky soiling including the nasty ballpoint ink.
    And it does help to release those tenacious dye-transfer stains especially on light colored leathers easily without resorting to unnecessary color refinishing.
    Its natural draggy-feel protection increases the leather resistance to wet and dry rubs, thus reduce stretch, scuff and abrasion.
    It is also used as a scuff repairer, filling and concealing surface scuffs to improve appearance.
    The drag produces an unforgettable familiar sound sweet to the ears when leather rubs.

    Let us know your progress with pictures!

    Roger Koh
    Leather Doctor®
    [email protected]

  4. #4
    Join Date
    Jun 2009
    Posts
    106

    Default Where to go from here?

    Sofa looks streaky all over. This is after being dyed. Not sure what went wrong. It does not look uniformed. And is there anything that we can do to correct this issue?












  5. #5
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    In every stage of the wet and dry prep process – the aim is to prepare the existing leather condition with evenness avoiding streaks or blotchiness.

    The prep surface beauty or ugliness of the leather surface will be magnified many times over once the topcoat is applied.

    This is what we see in these pictures are the incorrect end result of wet or dry prep.

    Streaks are evident of using razor-60 that produces this unevenness.

    My recommended procedure post #3 does not suggest the need of using razor-60.

    And the need of using razor-60 is for shaving off deteriorated topcoat to produce an even surface absorption, which also can become counterproductive as in this case.

    To correct the problem – the entire panels has to look uniform.

    And my recommendation is as follows:

    Step 1 - Leather Surface Wetting Tension Inspection and Correction:
    On the back panel choose a section and spray Hydrator-3.3 to check for uneven absorption of the leather surface.
    Even it out with Razor-60 and or wet 1200-1500 sanding.
    It is always safer to work the Razor-60 while the surface is wet or damp (just like shaving our own skin).

    Step 2 – When dry and Dry Prep - test out the dyeing (stain or coat) system on the back panel to see which produce the best result.

    Roger Koh
    Leather Doctor®

  6. #6
    Join Date
    Jun 2009
    Posts
    106

    Default After wet sanding & redye.

    1. Side of sofa.


    2. Back of sofa.


    3. Close up of back of sofa.

  7. #7
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    It is such a relief to see the recovery!

    We cannot call ourselves an expert without making mistake and learn from it.

    Do you have enough dyestuff to complete it?

    Roger Koh

  8. #8
    Join Date
    Jun 2009
    Posts
    106

    Default

    Yes, we need more dye to finish the job. We are low on both. One concern we have is the dye looks too dark. Should it be that dark or are we over applying the dye? Another concern we have is the oil/grease on the arm of the sofa.


  9. #9
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Oil/grease on the arm of the sofa.

    Use Degreaser-2.2 > Acidifier-2.0 (reduce bleeding).

    the dye looks too dark

    Use Clear to reduce the color saturation.

    Use Clear-177 for Aniline Pure-21 and Clear-777 for Aniline T’parent-27.

    Another way is to use dry application by increasing the air volume and reduce feed – very dry fine spray.

    And do not forget - when wax pull-up leather stretch the color becomes lighter - test it out!

    Email me the products that you need to finish off this job.

    Roger Koh

  10. #10
    Join Date
    Aug 2008
    Posts
    663

    Default

    Roger, I'm working with Jermaine today.
    I want to finish preping the sofa while we wait for the dye to come.

    I applied Degreaser 2.2 by sponge, I agitated with eraser, I covered with plastic. I'm going to let dwell for 30 Minutes.

    Now what? Rinse with Acidifier, extract with towels / repeat?

  11. #11
    Join Date
    Aug 2008
    Posts
    663

    Default

    Roger, when we get all the oil out, the grain is raised and doesn't look lik the rest. How do we repair the grain?

  12. #12
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    I would apply the Degreaser-2.2 with the leather Brush-1 (horsehair).

    During the Degreaser-2.2 extraction with paper rags reveal bleeding – Acidifier-2.0 is recommended to do the rinsing otherwise use Rinse-3.0 (A thorough wetting with Hydrator-3.3 will help to move suspended soiling through the wicking process more effectively – give it a try).

  13. #13
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    When aniline leather grain is damage repairs will have a darkening effect.

    For leather structure repair use Impregnator-26 (for penetrating repair).

    For surface raised grain use a mix of Impregnator-26 with leather Bond-3D.

    Don't forget all repairs when used transparent dyes the repairs see thru.

    It’s unless Aniline T’lucent-25 is used to hide the repair with partial opacity (that may alter the look too).

  14. #14
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Aniline Pure-21 is recommended to be added to the Impregnator-26 and Leather Bond-3D.

    Practice the mixture on a scrap simulated identical damage prior to actual application.

    I would use a Paasche airbrush to do the job to avoid steaks.

    It would be good if you can show the skin damages.

  15. #15
    Join Date
    Jun 2009
    Posts
    106

    Default

    Should we continue working on this area to make sure the oil & grease is gone? And what is the proper procedure to repair? Spraying on impregnator with the dye or applying with a foam brush?


  16. #16
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Rework the grease out!

    The grease is all on the “low valleys”.

    The “highlands” is clean.

    Apply the Degreaser-2.2 and squeeze it with a plastic card to drive it into the valleys.

    Gentle agitation with Leather Brush-1 for 5 – 10 minutes, then soak with rinse-3.0, agitate with the same brush and extract with paper rags (no scrubbing).

    When rag shows clean – spray Fatliquor-5.0 to strengthen the leather, and then repeat with thorough wetting the entire area with Hydrator-3.3 (helps to move suspended grease particulates from the leather structure through the wicking process.

    You can extend the leather surface tight with tissue then a towel on top during the slow wicking process.

    When dry, use Nubuck Brush-2 to gently dislodge the suspended dry soil particulates from the “valleys”.

    You will surely see a great improvement.

    I will further instruct you from there, after I see pictures.


    You may have a few more process to go, am I right?

    Aniline Pure-21 > Hydrator-3.3 > Fatliquor-5.0 > Wax Effect-8.6 > Impregnator-26 + sanding > Adhesor-73 + sanding > Aniline T’parent-27 + sanding > Topcoat Aniline-79G + sanding > Leather Scent-D.

    Do you need the details at each steps – the how’s or the why’s?

    Roger Koh
    Leather Doctor®

  17. #17
    Join Date
    Jun 2009
    Posts
    106

    Default

    Where to go from here?


  18. #18
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Proceed and reinspect after Fatliquor-5.0, further wick-up residue from the "low-valleys" to be remove with nubuck Brush-2.

    Inspect whether the damaged area is smooth by hand.

    We may have do some repair by bringing the Impregnator-26 forward pruior to Wax Effect-8.6.

    Let me know your findings.


    Aniline Pure-21 > Hydrator-3.3 > Fatliquor-5.0 > (Inspect and remove wick-up residue) Impregnator-26 (repairs?) > Wax Effect-8.6

  19. #19
    Join Date
    Jun 2009
    Posts
    106

    Default Completed sofa.








  20. #20
    Join Date
    Aug 2008
    Posts
    663

    Default

    Roger, We have a problem, the leather sofa is now a different color, much too dark. The customer wants $1100.00 back. Is there a way to remove color?

    Here is a picture of the original swatch laying on a restored cushion.


  21. #21
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    The fastest process is to use Acetone, spray and strip to the leather crust.

    You may have to rehydrate and fatliquor thereafter to return to leather suppleness.

    Anyway test it out a panel first.

  22. #22
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Tips:

    There is a different when working with dyes and colors.

    In pigment colors, “what you see is what you get” and the top coatings makes not too much of a difference to determine color saturation it is only gloss or matte effect.

    In transparent Dyestuff “what you see is not what you get” Topcoat Aniline-79G can deepen the color saturation as much as 25%.

    Therefore it is always wiser to finish only a hidden panel to check for your final color match.

    I have often said that the dyeing is always an option – The top coating is the determine factor.

    Roger Koh
    Leather Doctor®

  23. #23
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    Tips:

    In addition to stripping with Acetone, Basifier-8.8 and d’Tarnish-1.3 helps.

    Basifier-8.8 is to be used as a rinse after Acetone to induce bleeding.

    And d’Tarnish-1.3 may help to “bleach” some dyes and re-stabilize the leather structure pH value before Hydrator-3.3 and Fatliquor-5.0


    Roger Koh
    Leather Doctor®

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •