These are the products you may need for the re-dyeing, assuming you do not need any repairs...
http://i300.photobucket.com/albums/nn4/Rogerkoh/Auxiliary3-1.jpg
Leather Dyeing & Coloring Auxiliary (3):
Leather Adhesion Coating,
Leather Topcoat Crosslinker &
Leather Colorcoat Flow Controller.
Leather Doctor® Adhesor-73
It’s an auxiliary for Pigmented and Aniline leathers refinishing.
This is an aqueous compact resin adhesion promoter to ensure proper adhesion prior to color coating.
It's also added to Aniline Dye-21 for dye coating absorption resistant areas to reduce color blotchiness.
And it’s also used after WaxEffect8.6 prior to top coating.
This product is also available in concentrate to be cut with distilled water at a ratio of 1: 1.
Thus a quart makes 2 quarts of Ready-To-Use product to save on shipping.
Ready-To-Use packing sizes are available in 60ml, 250ml and in Quart.
Concentrate packing sizes are available in quart (2 quarts).
Email
[email protected] for prices.
Note:
Strip clean of foreign contamination prior to application – use Prep-7.7 > Cleaner-3.8 > Rinse-3.0.
Instruction:
1] Shake well, hand padding preferred to ensure better anchorage for non-absorbent leathers.
2] Fine airbrushing for absorbent leathers to reduce patchiness.
3] Let dry naturally or speed dry with blow dryer.
3] Proceed with choice of further coating.
Leather Doctor® Thickener-48
This is an auxiliary aqueous carboxylated acrylic co-polymer thickening agent to stabilize color during spraying.
It’s to adjust the flow of color to improve hold-up especially on vertical panels and antiquing two-tone fashion leathers.
It is highly effective and maintains the viscosity over the period of use.
This product is available in 60ml and 120ml.
Email
[email protected] for prices.
Instruction:
1] Add 5 to 15% of total weight of color and stir simultaneously while adding.
http://i300.photobucket.com/albums/nn4/Rogerkoh/AnilineSystem12.jpg
Aniline Leather Dyeing System (12):
Aniline Black Dye,
Aniline Orange Dye,
Aniline Red Dye,
Aniline Red-Brown Dye,
Aniline Yellow Dye,
Aniline Dark-Brown Dye,
Aniline Rubine Dye &
Aniline Blue Dye.
Aniline Natural Topcoat,
Aniline Waxy Matte Topcoat &
Aniline Gloss Topcoat.
Leather Doctor® Aniline Dye-21
It’s for staining absorbent aniline leathers.
This is a new generation aqueous transparent staining aniline dyestuff that is more lively and brilliant than most liquid dyes.
It’s to provide a more superior light fastness and fades resistance than most standard liquid dyes.
For coating aniline leathers that has existing topcoating; add up to 30% Adhesor-73 to even out appearance.
Standard colors available in Black-115, Orange-157, Red-180, Red-Brown-159, Yellow-128, Dark-Brown-124, Rubine-113 and Blue-119.
This product is also available in concentrate to be cut with distilled water at a ratio of 1: 8.
Thus a 120ml makes 1.14 quarts of Ready-To-Use product to save on shipping.
Ready-To-Use packing sizes are available in 60ml, 250ml and in quart.
Concentrate packing sizes are available in 120ml (1.14), 250ml (2.37) and quart (9 quarts).
Email
[email protected] for prices.
Instruction:
1] Prep clean - use Prep-4.4 follows by Cleaner-3.8 then Rinse-3.0.
2] When prep clean using Degreaser-2.2 either rinse with Acidifier-2.0 for bleeding control or with standard Rinse-3.0.
3] Inspection when dry – use leather Eraser-4 to remove wick-up soiling particulates.
4] Shake well before application.
5] For adhesion surface coating - add 10 to 30% Adhesor-73 (less is more natural).
6] Airbrush to even out the color avoiding streaks or drips.
7] Blow dry in-between coats until desired result is achieved.
8] Leather rejuvenation – use Hydrator-3.3 follows with Fatliquor-5.0.
9] Topcoat protection to match original luster - use Aniline Topcoat-89N(natural), Aniline Topcoat-59M (waxy matte) or Aniline Topcoat-79G (gloss).
Leather Doctor® Aniline Topcoat-79G
It’s a gloss finish for upholstery Aniline leathers.
This is an aqueous fine particular size urethane resin emulsion topcoat.
It’s to protect aniline dyestuff with excellent toughness and flexibility.
This product is also available in concentrate to be cut with distilled water at a ratio of 1: 1.
Thus a quart makes 2 quarts of Ready-To-Use product to save on shipping.
Ready-To-Use packing sizes are available in 60ml, 250ml and in quart.
Concentrate packing sizes are available in quart (2 quarts).
Email
[email protected] for prices.
Instruction:
1] Apply after Aniline Dye-21; otherwise prep clean - use Prep-4.4 follows with Cleaner-3.8 then Rinse-3.0.
2] Pad or fine spray without streaks or drips.
3] Non-Stick, Rub-Resistance buttery-feel protection with a classic leather scent - use Protection-B+ (leather Scent-B).