PDA

View Full Version : Pigmented (Mono-Tone) - Ekornes Stressless – armrest issue!



Questions!
08-25-2014, 10:56 AM
I think I sent you a photo of the back of the chairs that do not have any wear and you were going to take a look at them then confirm that the only kit I need is a P3.

#1
3727


#2
3728


#3
3729

Roger Koh
08-25-2014, 11:15 AM
A P3 kit at this stage is to perform a corrective cleaning to remove accumulated surface soiling accumulation.
Secondly is to rejuvenate the leather structure below surface for suppleness reducing or preventing stiffness that eventually leads to cracks when stressed or flexed. Lastly, you have the Protector-B+ that will reduce sticky soiling and increase rub-resistant from wearing out the color finishing.

But, picture #1 & #2 has shown wear into the leather crust and cracks that once the accumulated soiling is removed may become more obvious. At this leather worn and crack stage color refinishing is highly recommended with Kit Sa7.cl. Color matching services available at: http://www.leatherdoctor.com/servlet/the-Service-%E2%80%93-Custom-Color-Matching/Categories


3730
Leather Doctor Kit P3 – Pigmented Leather Care Kit
Leather Doctor® Kit P3, pigmented leather care kit is an innovative leather-safe (pH 3 - 5) system developed for keeping leather at their highest level of appearance besides maintaining their structural chemistry integrity and enhancing their suppleness. Pigmented finishes develop micro crazing as it ages and heat dries out the fat and oil from these weak point and stitching holes. The diminishing of the fat and oil empties the leather that results in creases and wrinkles. Stiffness to the leather is another sign of fat and oil diminishing that collapse the inter fibrillary spaces making the fiber becomes stick together and when flexed during used will lead to cracks. Periodic use of Hydrator-3.3 to hydrate the stick together fibers prior to fat and oil replenishing with Fatliquor-5.0 will keep the leather supple and strong. Thus, reduce the premature ageing of the leather against stiffness and cracking. The surface wear of the leather is greatly reduced when friction noise is kept low. The noise reduction is accomplished with rub-resistant Protector-B+ that imparts a natural buttery-feel. Periodic cleaning and rinsing with Cleaner-3.8 follows by Rinse-3.0 to the body contact area helps reduce greasy soiling build-up. Removing of unwanted stains such as ink or the common new blue jeans is accomplished with Prep-7.7. Note that the mentioned product suffix denotes it pH value. This kit comes with reduced weight option to save on shipping thus the 250ml concentrate ratio such as Clean-3.8, Rinse-3.0, Hydrator-3.3 and Fatliquor-5.0 has to be cut or filled up with distilled water prior to use.

Instruction:

Preventive Care:
A non-stick, rub-resistant protection is recommended to be in place before putting the leather to daily use. Protector-B+ imparts a soft natural buttery-feel that enhances the leather luxuriously to the sense of touch. The non-stick surface shields the leather from sticky soiling thus prolonging the high level of appearance. Rub-resistant abilities reduce friction noises that translate into less friction wear as one slide in and out of auto seats effortlessly with less stress to the seat bolsters. This leather-scented protector diffuses a classic leather scent that boost the sensuous leather more appealing to the leather lover. This protection care commences at the end of each level of routine, periodic or restorative cleaning cycle. A simply spray and wipe prolongs the need for cleaning heavy soiling.
1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

Routine Care:
Routine care includes procedures such as general dust cleaning, attending to spots and stains as required especially the neutralizing of swear stains from shifting alkaline. Thus prevents leather from tackiness. A routine non-stick rub resistant protection after neutralizing rinse helps keep leather interior in a more attractive and healthy state while preventing premature wear.
1. Spray Rinse-3.0, horsehair Brush-1 agitates and towel extract until it shows clean.
2. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

Periodic Care:
Periodic care is recommend before soiling causes damages to the finishing. This keeps leather consistently clean and healthy at all times. Driver’s seat would require more frequent attention than the other less frequent used seats. While the leather steering wheel and the gearshift knob get the most of body oil and sweat contacts.

1st phase – Periodic Care:
1. Spray Clean-3.8 and agitate with horsehair Brush-1; ensuring a uniform application over the entire surfaces a section at a time.
2. Towel extract until it shows clean.
3. Remaining residues are spray rinse with Rinse-3.0 and towel extract to a squeaky-clean.
4. Let dry and inspect for satisfaction, otherwise repeat cleaning process as necessary or proceed to hydrating.

2nd phase – Hydrating:
Although pigmented leathers surfaces are usually non-absorbent until micro crazing develops, it is the stitching rows and perforated holes that are usually vulnerable. These weak areas when wet and dry again have the tendency for the fibrils to become stick together resulting in stiffness and when stressed may lead to premature cracks. Hydrating is essential to relax and separate the stick together collapsing fibrous structure. Besides, charging the protein fiber ionic positive for a more effective hydrogen bonding with the ionic negative fatliquor.
1. Spray Hydrator-3.3 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
2. Let dwell 10 to 30 minutes depending on severity of dryness with optional plastic cling wrapping to control evaporation for a longer dwell time to plumps the leather more effectively.

3rd phase – Fat and Oil Replenishing:
Fatliquor evaporates as VOC (volatile organic compound) when temperature rises especially from exposed micro crazing, perforation and stitching rows. Periodic fat and oil replenishing maintains the leather’s structure integrity and pliability thus strengthen these exposed leather from cracking.
1. Spray Fatliquor-5.0 in like manner as Hydrator-3.3 and let dry naturally.
2. Repeat application in between drying until saturated.
3. Leave the leather for slow natural drying for extra softness.
4. Wipe surface strays with Hydrator-3.3 to free of sticky residue.

4th phase – Preventive Care:
1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

Restorative Care:
Restorative care is the ultimate corrective or salvage care system that removes accumulated soiling including aged conditioners to its original OEM finishes. Accumulated soiling that fills creases is often mistaken for cracks. Restorative cleaning is performed by using Prep-7.7. It works by chemical reaction to emulsify soiling through its penetrating, lubricating and suspending power. Its thick as honey viscosity facilitates coating the surface for effective dwell time. Horsehair detailing Brush-1 is recommended to worked into heavily soiled areas sufficiently to avoid excessive agitation that might damage already weaken finishes especially on heavily used areas. For extreme cases, the Prep-7.7 can stay continuous for up to 72 hours to do its work safely.

1st phase - Restorative Cleaning:
1. Apply Prep-7.7 and agitate with horsehair Brush-1, ensuring a uniform application over the entire surfaces a section at a time.
2. Allow a dwell time of 10 to 30 minutes or before it dries prior to towel extraction until it shows clean.
3. Sticky residue is removed by Cleaner-3.8 with gentle brush agitation and towel extraction until it shows clean.
4. Remaining residues are spray rinse with Rinse-3.0 and towel extract to a squeaky-clean.
5. Let dry and inspect for satisfaction, otherwise repeat Prep-7.7 application with a longer dwell time as necessary or proceed to hydrating.

2nd phase – Hydrating:
Although pigmented leathers surfaces are usually non-absorbent until micro crazing develops it is the stitching rows and perforated holes that are usually vulnerable. These weak areas when wet and dry again have the tendency for the fibrils to become stick together resulting in stiffness and when stressed may lead to premature cracks. Hydrating is essential to relax and separate the stick together collapsing fibrous structure besides charging it ionic positive for more effective hydrogen bonding with the negative ionic fatliquor.
1. Spray Hydrator-3.3 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
2. Let dwell 10 to 30 minutes depending on severity of dryness with optional plastic cling wrapping to control evaporation for a longer dwell time to plumps the leather more effectively.

3rd phase – Fat and Oil Replenishing:
Fatliquor evaporates as VOC (volatile organic compound) when temperature rises especially from exposed micro crazing, perforation and stitching rows. Periodic fat and oil replenishing maintains the leather’s structure integrity and pliability thus strengthen these exposed leather from cracking.
1. Spray Fatliquor-5.0 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
2. Repeat application in between drying until saturated.
3. The leather is left for slow natural drying for extra softness.
4. Surface strays are wipe with Hydrator-3.3 to free of sticky residue.

4th phase – Preventive Care:
1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gearshift knob after shaking well spread with lint free towel and is ready for use when dry.


3731
Leather Doctor Kit Sa7.cl – Semi-Aniline Leather Color Refinishing Kit http://www.leatherdoctor.com/servlet/the-385/Leather-Doctor-Kit-Sa7.cl/Detail
Leather Doctor® Kit Sa7.cl, micro-pigmented leather color refinishing kit is design for a holistic restoration approach to not only the finishes but also rejuvenating the leather for suppleness. Most of these repairs may range from missing finishes to abrading damages into the leather structure. Some expose areas may be contaminated with foreign soiling that includes conditioners, protectors, body oil, grease and sweat or alkaline overexposure from cleaners. A comprehensive repair for a long-term lasting solution will require a holistic approach to deal with both the exposed structure and surface finishes. The practical and functional softness and strength of the leather depends on the health of the structure with average thickness between 0.9 to 1.2mm from stiffness and cracking. The aesthetic aspect of the leather finishes averages 0.02mm (or 20 micron) in thickness for practical compressing and flexing from cracking. A leather-safe restoration system begins by stripping with Stripper-2.3 and rinsing with Rinse-3.0. Degreasing with Degreaser-2.2 follows with Acidifier-2.0. The suffix numbers of these four products denotes it pH value for recharging the protein fiber ionic positive besides the act of decontamination. The leather integrity is revitalizes once the ionic attraction between the positive protein fiber and its negative leather constituents like the tanning agent and fatliquor (fat, oil and water) is initiated. Leather rejuvenating system for softness and strength is accomplishes with Hydrator-3.3 follows with Fatliquor-5.0. Surface uneven absorption is seals with Adhesor-73 to reduce the need for color over-coating thus increase its flexibility and stretchability from premature cracking. Protector-B+ imparts a non-stick rub-resistant surface with a buttery feel, reduces noises that translate into less friction wear. As the leather surface is well lubricated it reduces compression when comes to heavy body contact thus reduces compressed creases and wrinkles.
Instruction:

Stripping Existing Deteriorating Finishes:
1. Cover and tape off frames, trims and protect flooring.
2. Mist sprays Stripper-2.3, Eraser-4 scrub with help of 2000-grit sandpaper feathering out seamlessly and towel extract for an even appearance.

Degreasing:
1. Shake Degreaser-2.2 to gel prior to use with a repeat shake and rest until it gels.
2. Transfer to Eraser-4; agitate to saturate the stain, feather out to the entire section.
3. Towel extracts suspended soiling after 10 to 30 minutes or before it dries until it shows clean.
4. Spray Acidifier-2.0, towel extract until it shows clean to a healthy squeak.

Hydrating:
1. Spray Hydrator-3.3 saturating the stain area and feather out for an even appearance.
2. Covering with tissue paper without airspace to trap wick up stains instead of remaining on the leather surface as it dries.
3. Peel tissue paper when crispy dry and use Eraser-4 to erase surface residue prior to fat and oil replenishing.

Fat and Oil Replenishing:
1. Spray Hydrator-3.3 to precondition the leather prior to fat and oil replenishing.
2. Spray Fatliquor-5.0 and redistribute with foam brush until saturation.
3. Repeat application each time water contents evaporate until fully saturated.
4. Drive remaining surface remnants free of milky fat and oil until it turns clear with Hydrator-3.3.
5. Allow natural drying for extra softness.

Dry Prep:
1. Erase wick-up residue with Eraser-4 prior to repairs.

Adhesion Promotion Coating:
1. Apply Adhesor-73 by foam brush to seal surface uneven absorption rate and promote adhesion simultaneously.

Color Coating:
1. Apply Micro-54 by foam brush, varnishing brush or airbrushing for professional result.
2. Fine dry atomize dispersion with more air is achieve with 80 to 100psi of air pressure.
3. Light spray is preferred and let dry in between coats to build up colorcoat.

Topcoating:
1. Shake the product well and apply by airbrushing for professional result.
2. Use lint free paper towel to even out drips and streaks.
3. Speed dries between coats with help of hair dryer.
4. 2000-grit sanding may applies to improve touch and appearance.

Rub-Resistant Protection:
1. Mist sprays Protector-B+ redistribute with a foam brush / paper towel and ready for use when dry.


Use this Pigmented (P) leather problem solving guide as reference:

3732