Results 1 to 2 of 2

Thread: Maserati 2012 GranTurismo Sport White Leather Seats with some Clothing Color Transfer.

  1. #1
    Join Date
    Feb 2012
    Posts
    564

    Default Maserati 2012 GranTurismo Sport White Leather Seats with some Clothing Color Transfer.

    I have a Maserati with white leather seats. I have experienced some color transfer and would be interested in maintaining the leather properly. I would like advice as to which leather kit I should purchase.

    I wanted to make sure that I get the proper kit to not only remove transfer stains, but also to properly treat the leather car seats to keep them in optimal condition.

    The car seat in the #2 photo is basically in need of cleaning and conditioning, I think, in order to protect it. The #3 photo shows a small bluish spot, which tends to occur now and then. They are most likely color transfer from clothes.

    #1
    Name:  photo 1.JPG
Views: 824
Size:  963.5 KB



    #2
    Name:  photo 1 copy.JPG
Views: 565
Size:  821.7 KB



    #3
    Name:  photo 2.JPG
Views: 500
Size:  919.5 KB
    Last edited by Questions!; 03-07-2014 at 09:31 AM.

  2. #2
    Join Date
    Feb 2007
    Location
    Greater Vancouver, Canada.
    Posts
    5,102

    Default

    A light pastel white leather seats will show soil pick-up quite easily. A routine maintenance with Protector-B+ will simple reduces sticky soiling and reduces rub-on transfer from clothing. Besides periodic and corrective maintenance, stubborn dyestuff stains are removed without harsh scrubbing that may deteriorate the finishes making the surface more absorbent to on going soiling. A “reverse-transfer” technique utilizing a stretchable paper towel with Prep-7.7 for up to a period of 72 hours with in-between inspection for satisfaction is proven to produce a non-destructive leather-safe removal for most dyestuff and ink stains.

    >>> I would like advice as to which leather kit I should purchase.
    See this Leather Doctor® Kit Ap7.di from: http://www.leatherdoctor.com/servlet...ers/Categories


    Roger Koh
    Leather Care Consultant
    www.LeatherDoctor.com
    [email protected]


    Product Information

    Name:  Ap3.JPG
Views: 556
Size:  1.48 MB
    Leather Doctor® Kit Ap7.di, auto pigmented (perforated) leather dye and ink remover kit is an innovative concept of removing blue jeans dye and ink stains featuring a “reverse transfer” technique utilizing a paper towel over the dwelling Prep-7.7. Prep-7.7. It works by penetrating, lubricating and suspending the stains on dwell time and the paper towel reverse absorb the stain instantaneously from the leather. Prior failed attempt with set-in stains may require the help of Bleach-9.9 as booster to the Prep-7.7 to remove the residual stains. Clean sticky residue with Cleaner-3.8, rinsed with Rinse-3.0 and pH balanced with Acidifier-2.0 when Bleach-9.9 is cooperated. Hydrator-3.3 relaxes stiff leathers prior to fat and oil replenishing. Fatliquor-5.0 rejuvenates the leather structure with softness and suppleness when dry. MicroTop-54D is an option for renewing the finish from friction wear. Protector-B+ imparts a non-stick rub-resistant protection with a buttery feel that shield against sticky soiling and reduce friction noises. Note that the mentioned product suffix number denotes its pH value in this holistic leather-safe dye and ink stain removal system.

    Instruction:

    Testing with Prep-7.7
    1. Cut out a piece of paper towel from the kit not bigger than our thumb size and soak it with Prep-7.7.
    2. Test it on the worst stain area and inspect every 24 hours with fresh application until the stain is gone.
    3. Observe if there is sign of stain removal, if it does, the stain will eventually be remove with repeat application.
    4. To secure the test patch from dislodging wrapped it over with see through cling wrap.
    5. When stain is removed with satisfaction, clean off the sticky residue with Cleaner-3.8 follows with Rinse-3.0 until a
    squeaky-feel.
    6. The lack of a healthy squeaky feel may be the result of worn out topcoat, reapplication with MicroTop-54M is
    recommended.
    7. Apply a soak out paper towel with Acidifier-2.0 over the area until dry to strengthen the finish prior to topcoat application.
    8. When test after 72 hours shows poor response, Bleach-9.9 may be used to boost the Prep-7.7.

    Mixing Ratio (1: 2: 2)
    1. A mixing ratio guide by weight is 1 part Bleach-9.9: 2 parts Prep-7.7: 2 parts Hot water.
    2. From the mixing bottle, a small test portion Bleach-9.9 is first added into the bottle follow with Prep-7.7 adding and stirring
    into a paste.
    3. Hot water is dripped into the bottle using the pipette to activate the bleach and stirring into a creamy paste.

    Testing with Bleach-9.9
    1. Apply onto an inconspicuous or hidden area and leave it for a 12 hours inspection for discoloration.
    2. Remove residue with damp wiping and cleaning sticky residue with Cleaner-3.8 follows with Rinse-3.0.
    3. Cut out a paper towel, soak with Acidifier-2.0 and place on the test spot until naturally dry to neutralize the alkalinity.

    Note
    If testing with Bleach-9.9 bleach shows side effect, abandon and continue only with Prep-7.7.

    Actual Application
    Repeat testing successes to the actual application.


    Instruction:

    Preventive Care:
    A non-stick, rub-resistant protection is recommended to be in place before putting the leather to daily use. Protector-B+ imparts a soft natural buttery-feel that enhances the leather luxuriously to the sense of touch. The non-stick surface shields the leather from sticky soiling thus prolonging the high level of appearance. Rub-resistant abilities reduces friction noises that translate into less friction wear as one slide in and out of auto seats effortlessly with less stress to the seat bolsters. This leather-scented protector diffuses a classic leather scent that boost the sensuous leather more appealing to the leather lover. This protection care commence at the end of each level of routine, periodic or restorative cleaning cycle. A simply spray and wipe prolongs the need for cleaning heavy soiling.
    1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

    Routine Care:
    Routine care includes procedures such as general dust cleaning, attending to spots and stains as required especially the neutralizing of swear stains from shifting alkaline. Thus prevents leather from tackiness. A routine non-stick rub resistant protection after neutralizing rinse helps keep leather interior in a more attractive and healthy state while preventing premature wear.
    1. Spray Rinse-3.0, horsehair Brush-1 agitates and towel extract until it shows clean.
    2. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

    Periodic Care:
    Periodic care is recommend before soiling causes damages to the finishing. This keeps leather consistently clean and healthy at all times. Driver’s seat would require more frequent attention than the other less frequent used seats. While the leather steering wheel and the gear shift knob get the most of body oil and sweat contacts.

    1st phase – Periodic Care:
    1. Spray Cleaner-3.8 and agitate with horsehair Brush-1; ensuring a uniform application over the entire surfaces a section at a time.
    2. Towel extract until it shows clean.
    3. Remaining residues are spray rinse with Rinse-3.0 and towel extract to a squeaky-clean.
    4. Let dry and inspect for satisfaction, otherwise repeat cleaning process as necessary or proceed to hydrating.

    2nd phase – Hydrating:
    Although pigmented leathers surfaces are usually non-absorbent until micro crazing develops, it is the stitching rows and perforated holes that are usually vulnerable. These weak areas when wet and dry again have the tendency for the fibrils to become stick together resulting in stiffness and when stressed may lead to premature cracks. Hydrating is essential to relax and separate the stick together collapsing fibrous structure. Besides, charging the protein fiber ionic positive for a more effective hydrogen bonding with the ionic negative fatliquor.
    1. Spray Hydrator-3.3 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
    2. Let dwell 10 to 30 minutes depending on severity of dryness with optional plastic cling wrapping to control evaporation for a longer dwell time to plumps the leather more effectively.

    3rd phase – Fat and Oil Replenishing:
    Fatliquor evaporates as VOC (volatile organic compound) when temperatures rises especially from exposed micro-crazing, perforation and stitching rows. Periodic fat and oil replenishing maintains the leather’s structure integrity and pliability thus strengthen these exposed leather from cracking.
    1. Spray Fatliquor-5.0 in like manner as Hydrator-3.3 and let dry naturally.
    2. Repeat application in between drying until saturated.
    3. Leave the leather for slow natural drying for extra softness.
    4. Wipe surface strays with Hydrator-3.3 to free of sticky residue.

    4th phase – Preventive Care:
    1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gear shift knob after shaking well spread with lint free towel and is ready for use when dry.

    Restorative Care:
    Restorative care is the ultimate corrective or salvage care system that removes accumulated soiling including aged conditioners to its original OEM finishes. Accumulated soiling that fills creases is often mistaken for cracks. Restorative cleaning is performed by using Prep-7.7. It works by chemical reaction to emulsify soiling through its penetrating, lubricating and suspending power. Its thick as honey viscosity facilitates coating the surface for effective dwell time. Horsehair detailing Brush-1 is recommended to worked into heavily soiled areas sufficiently to avoid excessive agitation that might damage already weaken finishes especially on heavily used areas. For extreme cases, the Prep-7.7 can stay continuous for up to 72 hours to do its work safely.

    1st phase - Restorative Cleaning:
    1. Apply Prep-7.7 and agitate with horsehair Brush-1, ensuring a uniform application over the entire surfaces a section at a time.
    2. Allow a dwell time of 10 to 30 minutes or before it dries prior to towel extraction until it shows clean.
    3. Sticky residue is removed by Cleaner-3.8 with gentle brush agitation and towel extraction until it shows clean.
    4. Remaining residues are spray rinse with Rinse-3.0 and towel extract to a squeaky-clean.
    5. Let dry and inspect for satisfaction, otherwise repeat Prep-7.7 application with a longer dwell time as necessary or proceed to hydrating.

    2nd phase – Hydrating:
    Although pigmented leathers surfaces are usually non-absorbent until micro crazing develops it is the stitching rows and perforated holes that are usually vulnerable. These weak areas when wet and dry again have the tendency for the fibrils to become stick together resulting in stiffness and when stressed may lead to premature cracks. Hydrating is essential to relax and separate the stick together collapsing fibrous structure besides charging it ionic positive for a more effective hydrogen bonding with the negative ionic fatliquor.
    1. Spray Hydrator-3.3 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
    2. Let dwell 10 to 30 minutes depending on severity of dryness with optional plastic cling wrapping to control evaporation for a longer dwell time to plumps the leather more effectively.

    3rd phase – Fat and Oil Replenishing:
    Fatliquor evaporates as VOC (volatile organic compound) when temperature rises especially from exposed micro-crazing, perforation and stitching rows. Periodic fat and oil replenishing maintains the leather’s structure integrity and pliability thus strengthen these exposed leather from cracking.
    1. Spray Fatliquor-5.0 control and spread with foam brush to hydrate especially the stitching rows and perforated sections.
    2. Repeat application in between drying until saturated.
    3. The leather is left for slow natural drying for extra softness.
    4. Surface strays are wipe with Hydrator-3.3 to free of sticky residue.

    4th phase – Preventive Care:
    1. Apply Protector-B+ to the seats and Protector-D to steering wheel including the gearshift knob after shaking well spread with lint free towel and is ready for use when dry.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •