Louis Vuitton Keepall Bag - would Kit-V3 be a great alternative for replacing the darkened leather parts?

>>> What is the best ways in restoring and cleaning luxury handbags without bringing the bags to the boutiques?
Technical knowledge is the key to success in restoring and cleaning luxury handbags. And if we follow the principles and practices of a modern tannery we can bring back another lease of life to the leather to a certain extend. If a system is leather science based and we follow simple instruction the result will be positively leather-safe with no side effect.

>>> We think the Leather Doctor Kit-V3 is ideal for cleaning and brightening old Vachetta leather on Louis Vuitton handbags, which would be a great alternative for replacing the darkened leather parts.

Leather Docor Kit-V3 is ideal for cleaning, conditioning and restoring the discoloration of this Keepall bag vachetta trimmings beautifully. But the darkening handles will need the extra Degreaser-2.2 and leatherEraser-4 to help, found in Kit-V4 instead.

My recommendation is to work from the simplest task upward, leaving the handles to perform last. Maybe start with the nametag first, second the strap both remove from the bag, third the 2 supports and the last the handles.

Instruction for the Tag, Strap and Support (with complete satisfaction before proceeding to the next item).

Dry Preparation:
1- Use LeatherEraser-4, and pre-clean soiling, prior to VachettaPro-1.2 application.

Cleaning:
2- Spray direct or transfers VachettaPro-1.2 to the horsehair Brush-1 or LeatherEraser-4 (for better traction), and brushes or agitates the leather. Suspended soiling is towel extract, with a more absorbent cotton terry towel or Towel-5. Repeat 2 and 3 until towel shows clean.

Rinsing & pH Balancing:
3- Spray direct or transfers Acidifier-2.0 to the horsehair Brush-1, and brush or agitate follows with towel extract until towel shows clean.

Hydrating (Leather Relaxing):
4- While the leather is still damp, apply Hydrator-3.3 to saturate, evaporation control with plastic cling wrapping, or seal into a zip lock bag. Allow (1hour to 72 hours) control dwelling, will ensure full relaxation of the leather structure, and separating of any stiff stick together fibers.

Fatliquoring (Fat & Oil Replenishing):
5- With satisfaction and while still damp, apply Fatliquor-5.0 spraying direct or transferring to the foam Brush-3. Allow the product to be absorbed into the leather. However, the moisture content of the Hydrator-3.3 will need to be evaporated, to make space for the Fatliquor-5.0. Moreover, about 83.33% of water content when penetrated will also need to be evaporated. It is only the 16.66% of fat and oil that will eventually benefits the leather with suppleness. In each of the fatliquor drying cycle more is applied until further application only stays on its surface would end the application. (See more details here: http://www.leatherdoctor.com/fatliquor-5-0/).

6- Drying:
The leather is left to slow natural drying and before it finally dries, massage or flex it to dry for extra suppleness

7- Discoloration Control:
Vachetta-2.8 is spray or transfer to horsehair Brush-1 and lightly brush to saturate over the entire leather without leaving any dry lines and towel extract until towel shows clean. This is left to natural dry for reduction-oxidation to work out the discoloration. When dry inspect for satisfaction, otherwise repeat application.

8- Protection:
Apply Protector-D to the entire surface of the leather, leave to dry and is ready for use.

Let us see some result before we continue to discuss the best approach to restore the handles.

For your readings:

Attachment 8289
http://www.leatherdoctor.com/kit-v4-...g-removal-kit/
Leather Doctor® Kit-V4: Vachetta Leather Darkening (result from body oil, grease and sweat constant contact) Removal Kit incorporates the Degreaser-2.2 and Eraser-4 essential for the removal of common body oil, grease and sweat problems especially to the handles degrading from browning to darkening and eventual cracking. The main culprit is also the sweat that eventually cracks the leather sooner or later and routine care with rinsing using Rinse-3.0 helps pH neutralize the sweat, Sanitizer-3.9 has with a dual function for both pH neutralizing and sanitizing from off-gassing bacteria activities would be a better choice. Darkening appearance from body contact and browning from liquid stain are two main inevitable common problems associated with naked unfinished vachetta leathers. Leather being absorbent absorb and accumulates body moisture from contact and when neglected resulted in a darkening appearance. Besides appearance the sweat with traces of urea may cause the protein fiber from shifting ionic negative (-ve) manifesting as tackiness and reverting to rawhide. Degreaser-2.2 solves the darkening effect by penetrating, lubricating and suspending the soiling particulates and simultaneously protonate the protein fiber ionic positive (+ve). The amphoteric protein fiber is further rinse and ionic positive (+ve) charge with Acidifier-2.0 to strengthen the ionic attraction between its other non-amphoteric ionic negative (-ve) leather constituents like the tanning agent and the fatliquor. This dual duty removes the unwanted soiling particulates and pH balance the pH chemistry integrity of the leather at the same time. Vachetta Leather Browning, blotchiness or discoloration is associated with general accumulation of liquid soiling and will require VachettaPro-1.2 > Acidifier-2.0 system to remove and also to pH balance alkaline over-exposure that cause the browning discoloration. Alkaline pH sensitive Vachetta leathers when neglected often suffer unsightly browning stain marks from a variety of liquid sources. Even apparent clean rain or tap water often leaves a lightening spot with an outer ring. The pH 7 alone of water will often cause a rippling effect on the tannin that destabilize and causes it to moves. The higher the pH value above water the darker the browning stain becomes. Browning correction is performed in two stages, a pre-cleaning and a post-treatment. Pre-cleaning soiling removal in combination with pH balancing the leather structure improves appearance and returns the pH chemistry integrity to its original pH neutral of between 3 and 5. When pre-cleaning becomes satisfactorily it is essential that leather rejuvenating continue while the leather is about 25% combine moisture level or terry towel extract until the towel shows dry. The reason being that when leather is wet and dry without sufficient fatliquor it will shrink and in extreme cases cracks when dry with insufficient fatliquor. A 15% of fat and oil moisture read with a leather moisture meter or equivalent when perfectly dry without the water content is a healthy leather and would never crack. Leather rejuvenating with Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 is a 1st-step hydrating the leather structure of stiffness and separates any stick together leather fibrils free or preconditioning it prior to the 2nd-step of fatliquor replenishing it. 5/6 of the fatliquor water contents will evaporates and only leaves 1/6 of the remaining fat and oil, the fat plumps the leather with fullness and the oil lubricates the fibrils like millions of interlocking hinges for sliding over one another for suppleness with softness and tensile-strength from breaking. A fully saturated fat and oil with breathing pores makes the natural leather less absorbent to any liquid ingress. The 3rd-step is to remove any fatliquor fat and oil remnants that turns milky again from the leather surface with Hydrator-3.3, and preferably to move it into the leather instead with the horsehair Brush-1. A slow drying will produce a softer leather and flexing or massaging it while almost dry also helps in extra desired suppleness. The leather is scrutinized once again when dry for discoloration or undesired sun-tanning or ageing effect. It is then rejuvenated with a redox (reduction-oxidation) treatment using Vachetta-2.8. It is applied, brush and towel extract until towel shows clean. The final treatment is to even out and let to dry naturally for the product to take effect. Any powdery residue is wiped off with Hydrator-3.3 and let slow dry again. Protector-D enhances a rub resistant draggy-feel against friction rubs and is use routinely to conceal and fill scuffmarks. Body contact areas should be clean routinely with Clean-3.8 follows with Rinse-3.0 or Sanitizer-3.9, thereafter applied with non-stick protection and commence for another cycle of use. Darken and prolong body grease and sweat contacts will require a degreasing process with Degreaser-2.2 > Acidifier-2.0 system in most cases. Preventive cleaning and protection to shield against sticky soiling, with the abilities to heal and conceal lightening scuff and abrasion marks keeps the leather appearance level high at all times rather than relying on corrective or salvage cleaning where the cleaning appearance deteriorates and diminishes with each cycle. Note that the mentioned products suffix numbers denotes its pH value in this holistic approach to removing vegetable, plant and water stains from vachetta, saddlery and veg-tan leathers.

Tips 1 – Cracks Control:
Aged, dried or signs of leather cracking should be first leather rejuvenated with Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 system and let dry prior to Vachetta-2.8 treatment. This precaution is to prevent any further cracking accelerated to the leather. In other words, any leather dryness less then 7% of original fatliquor moisture content measured with a leather moisture meter or an equivalent wood moisture meter should first be rejuvenated to top up or replenish to its original fatliquor up to 15% prior to treatment with Vachetta-2.8. Due to “Van der Waal or London Forces” phenomenon in the drying process, the empty or insufficient of fatliquor in the leather fiber structure is likely to result in stiffer leather as the fibers becomes stick together. A slower natural drying will reduce the stiffness ill effect from the lack of fatliquor

Tips 2 – Appearance Control:
Water stain spotting may be done with a cotton swab until it shows clean. It is recommended that the entire panel be treated equally to an even appearance to eliminates any rings when dry thereafter. Treated panel may take up a lightening effect as it also reduces the sun tanning effect if any and recommend that the entire article be treated accordingly. Always pre-clean with VachettaPro-1.2 > Acidifier-2.0 prior to post-treatment with Vachetta-2.8 so as not to over-clean it too early.

Tips 3 – Suppleness Control:
Unlike other leather tanning type, vegetable-tanned leathers are more susceptible to cracks as it is characteristically more fatliquor thirsty. Dry leathers are handle with care for inspection and continue with rejuvenating it with Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 system.

Tips 4 – Sealing and Concealing Scuffing Control:
The final of the holistic Vachetta care system ends with Protector-D or the leather scented version of Protector-D+ to seal and conceal scuffing leaving the leather with its natural transpiration. For a lighter appearance "D" is recommended.

Instruction

A- Degreasing with Degreaser-2.2 > Acidifier-2.0 > Hydrator-3.3 system:
A1- Dry soil removal with Eraser-4. A2- Apply Degreaser-2.2 and agitate with horsehair Brush-1 or Eraser-4 and towel extract until towel shows clean. A3- Rinse off remaining residue with Acidifier-2.0 until towel shows clean. A4- Penetrated soiling are remove with the help of Hydrator-3.3 by saturating the leather structure and cling wrapping to control evaporation for up to 72hrs with replenishing the moisture high so that lodge soiling becomes loose. Plastic wrapping is replace with Towel-5 wrapped taut and tight without airspace so that soiling will reverse-transfer to the towel during the drying process and peel off. However, if leather has already shows evident of cracking, then it is highly recommended that Fatliquor-5.0 is replenished with repeat almost drying cycle and only at the least replenishment Towel-5 is introduced for the reverse transfer. Note that when leather becomes wet and dry again it will dry stiffer without any fat and oil and may accentuate the cracking effect. Also note that to have a more supple leather it is recommended that they are gently flexed or massaged from almost dry to dry to produce a softer leather. However on a combination issue with browning discoloration issue on the same panel VachettaPro-1.2 may be inserted into the combine ‘wet’ system as Degreaser-2.2 > VachettaPro-1.2 > Acidifier-2.0 > Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 system before it dries follows with the final ‘dry’ treatment of Vachetta-2.8 and ends with Protector-D in Kit-V4 holistic system.

B- Browning Discoloration Removal with VachettaPro-1.2 > Acidifier-2.0 system:
B1- Dry soil removal with horsehair Brush-1: terry towel or optional Eraser-4 depending on soiling severity prior to product application. B2- Pre-cleaning with VachettaPro-1.2: spray and saturate evenly with simultaneous agitation from horsehair Brush-1 and/or optional Eraser-4 for an even appearance and towel extract until it shows clean. Another option is to use a saturate cotton swab or a terry towel to do a test cleaning until it shows clean. Extend cleaning to the entire panel without leaving any dry area until towel shows clean for an even appearance. B3- Rinsing with Acidifier-2.0: spray and agitate with horsehair Brush-1 and towel extract until it shows clean. Proceed with Hydrator-3.3 while the leather is still damp.

C- Hydrating with Hydrator-3.3:
Hydrator-3.3 is evenly applied, agitated and spread with horsehair Brush-1 or FoamBrush-3” and towel extract for an even appearance prior to Fatliquor-5.0. Proceed with Fatliquor-5.0 while the leather is still damp.

D- Fatliquor Replenishing with Fatliquor-5.0:
Fatliquor-5.0 is a continuous process that proceeds immediately after satisfactory Hydrator-3.3 appearance inspection.The process is repeated when the leather is almost dry until the leather is saturated before it is let to a slow natural drying process. It will take up a seasoning effect in relation to the amount of fatliquor intake. 15% of fat and oil moisture level without any water content is the optimum moisture level when the leather is completely dry. Fat and oil moisture content is measurable with a leather moisture meter or equivalent. Penetrated stains are further fully saturated with Hydrator-3.3 allowing for structural water movement to floats or wicks any soiling particulates to the surface. The entire surface may be cling wrapped to control evaporation keeping at the highest level of moisture content for up to 72hrs. The cling wrapper may be removed and wicks up soiling towel extracted until towel shows clean. Fresh application is applied and ‘reverse-transfer’ technique with Towel-5 replaces the cling wrapper. Air bubbles or spaces is work out taut or stretch-tight with horsehair Brush-1 and let to dry. As the surface dries and the Towel-5 shrinks it will wick all water contents bringing soiling particulates through the Towel-5. It is then peel off the surface trapping the soiling particulates.

E- Redox (reduction-oxidation) treatment with Vachetta-2.8:
Product may be adjusted with distilled water to match desired appearance. E1- This product is highly recommended to treat leather after drying from Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 system. E2- Shake well, spray and saturate with horsehair Brush-1 or FoamBrush-3” for an even appearance and towel extract until it shows clean. E3- Extend cleaning to the entire panel when towel shows clean for an even appearance working out line or rings to an even appearance without leaving any dry area. E4- Let natural drying and inspect result. E5- Note: In most cases the treated panels will look lighter than other untreated panels, as the product not only corrects discoloration, it also reduces any ageing or sun-tanning effect (adjustment is made by an initial test and adjust product concentration accordingly with distilled water ratio 1: 1). The entire article is therefore recommended to be treated accordingly for an overall appearance.

F- Sealing and Concealing Light Abrasion and Scuffing with Protector-D:
Protector-D is applied for sealing and concealing light abrasion and scuffing, besides shielding the leather from the detrimental effect, soiling is becomes easier to remove during the routine care.

Roger Koh
Leather Care System Formulator
Consultant / Practitioner / Instructor / Coaching
web: www.leatherdoctor.com
forum: www.leathercleaningrestorationforum.com
email: [email protected]