Perforated Leather Seat Stain by Jeans and Leather Belt.

Either it is blue jeans or leather belt stains, it is proven that they are completely removed safely without unnecessary scrubbing, but relying on the penetrating, lubricating and suspending power of the working products.

Tips:
Avoid squeezing Prep-7.7 into perforated and stitching holes.
Cut out paper and apply to it prior placing it to the stain areas.

Roger
www.LeatherDoctor.com

Product information and general instructions:

Attachment 1483
Leather Doctor Kit Ap7.di – Auto Pigmented (perforated) Leather Dye / Ink Stain Removal Kit
Leather Doctor® Kit Ap7.di, auto pigmented (perforated) leathers dye and ink remover kit is an innovative concept of removing blue jeans dye and ink stains featuring a “reverse transfer” technique utilizing a paper towel over the dwelling Prep-7.7. Prep-7.7. It works by penetrating, lubricating and suspending the stains on dwell time and the paper towel reverse absorb the stain instantaneously from the leather. Prior failed attempt with set-in stains may require the help of Bleach-9.9 as booster to the Prep-7.7 to remove the residual stains. *Sticky residue is clean with Cleaner-3.8, rinsed with Rinse-3.0 and pH balanced with Acidifier-2.0 when Bleach-9.9 is cooperated. Hydrator-3.3 relaxes stiff leathers prior to fat and oil replenishing. Fatliquor-5.0 rejuvenates the leather structure with softness and suppleness when dry. MicroTop-54M is an option for renewing the topcoat from friction wear. Protector-B+ imparts a non-stick rub-resistant protection with a buttery feel that shield against sticky soiling and reduce friction noises. Note that the mentioned product suffix number denotes its pH value in this holistic leather-safe dye and ink stain removal system.

Instruction:

Testing with Prep-7.7
1. Cut out a piece of paper towel from the kit not bigger than our thumb size and soak it with Prep-7.7.
2. Test it on the worst stain area and inspect every 24 hours with fresh application until the stain is gone.
3. Observe if there is sign of stain removal, if it does, the stain will eventually be remove with repeat application.
4. To secure the test patch from dislodging wrapped it over with see through cling wrap.
5. When stain is removed with satisfaction, clean off the sticky residue with Cleaner-3.8 follows with Rinse-3.0 until a squeaky-feel.
6. The lack of a healthy squeaky feel may be the result of worn out topcoat, reapplication with MicroTop-54M is recommended.
7. Apply a soak out paper towel with Acidifier-2.0 over the area until dry to strengthen the finish prior to topcoat application.
8. When test after 72 hours shows poor response, Bleach-9.9 may be used to boost the Prep-7.7.

Mixing Ratio (1: 2: 2)
1. A mixing ratio guide by weight is 1 part Bleach-9.9: 2 parts Prep-7.7: 2 parts Hot water.
2. From the mixing bottle, a small test portion Bleach-9.9 is first added into the bottle follow with Prep-7.7 adding and stirring into a paste.
3. Hot water is dripped into the bottle using the pipette to activate the bleach and stirring into a creamy paste.

Testing with Bleach-9.9
1. Apply onto an inconspicuous or hidden area and leave it for a 12 hours inspection for discoloration.
2. Remove residue with damp wiping and cleaning sticky residue with Cleaner-3.8 follows with Rinse-3.0.
3. Cut out a paper towel, soak with Acidifier-2.0 and place on the test spot until naturally dry to neutralize the alkalinity.

Note
If testing with Bleach-9.9 bleach shows side effect, abandon and continue only with Prep-7.7.

Actual Application
Repeat testing successes to the actual application.